Prokits-industries SS-201 User Manual download pdf

PROKIT'S INDUSTRIES CO., LTD.

寶工實業股份有限公司

SS-201

www.prokits.com.tw

MINI SOLDERING

STATION

更換烙鐵頭

 注意：更換烙鐵頭前，一定要先拔除電源插頭，確認在沒有電源和烙

鐵頭溫度冷卻情況下操作，以免觸電和燙傷危險。

1. 用無牙尖嘴鉗，取下烙鐵頭

2. 用無牙尖嘴鉗，裝入烙鐵頭

再次確認烙鐵頭，已順利裝至正確位置



更換發熱元件：

 注意：更換發熱元件前，一定要先拔除電源插頭，確認在沒有電源和

烙鐵頭溫度冷卻情況下操作，以免觸電和燙傷危險。

1. 取下烙鐵頭

2. 鬆開螺絲，取出發熱元件。

鬆開拴緊手柄的螺絲，慢慢從手柄中取出發熱元件和電線。

3.取下發熱元件上，耐高溫塞頭。

3.取下發熱元件

拔開接線端，取下發熱元件。

4.更換新發熱元件

小心處理，切勿磨擦發熱元件電線，插入新發熱元件，接上接線端。

管內裝置有陶瓷發熱體，勿掉落或重振，以免損壞。

5.依拆開時的相反程序回裝手柄，並確實將手柄螺絲固定。

Thank you for purchasing the Pro'sKit SS-201 Mini Soldering

Station. Before using the SS-201 for the first time, please read the

following instructions.

CARE OF THE SOLDERING TIP

The SS-201 soldering tip is made with iron plated copper. If used

properly, it should last for a long time. The following steps will help

ensure a longer tip life.

1. Always keep the tip tinned before switching off or storing for any

period of time. Only wipe before use.

2. Do not keep the SS-201 set at a high temperature for a long period of 

 time as this will break down the surface of the tip.

3. Never clean the tip with coarse abrasive materials or files.

4. If an oxide film does form, it can be cleaned by lightly rubbing with a 

 600-800 grit emery cloth, isopropyl alcohol or equivalent, and then 

 immediately reheating and retinning the tip to prevent oxidation of the 

 wettable surface.

5. Remove the tip and clean every twenty hours of use, or at least once 

 a week, and remove any loose build up in the barrel.

6. Do not use fluxes containing chloride or acid. Use only rosin or  

 activated resin fluxes.

7. Do not use any compound or anti-seize materials on the wettable  

 surface.

MAINTENANCE

SOLDERING TIP REPLACEMENT

CAUTION: Tip replacement or cleaning should be done only when the

element is at room temperature.

1. Unplug the SS-201 station

2. Use a set of flat pliers(no teeth) to carefully remove the tip from the

heating element.

3. Replace with cleaned or new tip.

SOLDERING HEATER REPLACEMENT

1. Unplug the SS-201 station and ensure that the element has cooled

down.

2. Remove the soldering tip (see above).

3. Unscrew the nut that holds the heating element to the handle.

4. Use a set of flat pliers (no teeth) to pull out the rubber plug.

5. Feed the power cord up through the unit until the connector is visible.

6. Disconnect the heating element (2 pins).

7. Connect the new heating element and feed it back into the handle.

8. Replace the plug into the handle and retighten the nut.

9. Insert the soldering tip onto the new heating element.

選購配件

9SS-201-H  9SS-201-T

陶瓷發熱體  烙鐵頭

型號 SS-201

內容 規格尺寸

輸入電壓(V) AC110V / AC220V

消耗功率(W) 4~14W

電流(A) 0.07~0.16A(AC110V)

 0.035~0.07A(AC220V)

高壓1mA/1sec 1500VAC

絕緣電阻(Ω) >1MΩ

接地電阻(Ω) <0.1Ω

烙鐵頭溫度 (℃) ~330℃(~626℉)

手柄最高溫度(℃) < 50℃

發熱體電壓(V) AC12V(端子插卡式)

發熱體功率(W) 陶瓷12W/DC12V

內阻(Ω) 12Ω

標準配件 烙鐵頭、簡易烙鐵、架除錫海綿座、

 除錫海綿各1個、中英文說明書1本

重量(g) 860g

 (含標準配件、彩盒)

Model no. SS-201

Spec. Description

Input Voltage(V) AC110V / AC220V

Consumption(W) 4~14W

Current(A) 0.07~0.16A(AC110V)

  0.035~0.07A(AC220V)

Hight Voltage Test 1mA/1sec 1500VAC

Insulation Resistance(Ω) >1MΩ

Earth Resistance(Ω) <0.1Ω

Iron Tip Temperature (℃) ~330℃(~626℉)

Handle Temperature(Max)(℃) < 50℃

Package Contents SS-201 station w/soldering tip,

soldering stand, sponge, and

  user's manual

Weight(g) 860g

SS-201 迷你控溫焊台

產品特點：

• 採用精密電子控溫電路，精確控制溫度~330℃(~626℉)

• 獨特AC110/220V雙電壓可調式設計，具備保護電路，方便多國家、多地

區使用

• 焊台具防靜電功能，外型迷你輕巧，節省工作空間，方便攜帶

• 烙鐵小巧玲瓏，不易擋住視線，特別適合精密電子電路維修使用

• 適合手機維修、精密電路焊接、外派研發人員使用

面板操作：

使用前，注意事項：

1. 小心高溫操作

切勿在近易燃氣體、紙張或其他易燃物品附近使用本迷你控溫焊台。

發熱元件和烙鐵頭都十分炙熱，能灼傷人體。

切勿觸摸發熱體，或接觸體膚。

起動初時，可能因有水蒸氣會冒白煙，但過一會兒應就會恢復正常。

 注意：如果過了很久扔有白煙﹐請檢查是否有異物侵入

2.使用後，切記將電源插頭拔除

使用完畢，應將開關關閉，電源插頭拔除，等待若干分鐘發熱元件確

實冷卻後，再行收拾或離開。

3.切勿掉落或重掁

　發熱元件含有陶瓷，如果掉落或重振，會使陶瓷破碎。

4.勿拆開機身

5.長久不使用，應拔出電源插頭

當電插頭插電源時，即使是關上電源開關，也會有少量電流輸入，所以

如果您長久不使用，須拔出電源插頭。

6.剛開始使用時，如果無法確定所需溫度，請先將溫度調到最低，再逐漸

調整升高溫度，到適當為止。

除錫步驟

1.電源插頭插入電源插座。

2.按開電源開關

 發熱元件開始發熱。

 調整溫度控制鈕，稍等一會兒，待溫度穩定下來。

 我們建議您，可調整溫度在攝氏300度至350之間。

 注意：溫度如果超過攝氏400度以上，將快速破壞烙鐵頭上的保護層

，降低烙鐵頭使用壽命。

3.熔化焊錫

手持電烙鐵，取適量焊錫，接觸烙鐵頭尖部，讓烙鐵頭熔化焊錫，除

 了可以去除烙鐵頭上氧化物外，也可以保護烙鐵頭。

 除去多餘焊錫。

4.除錫或拔除零件

 對準並預熱所要除錫或拔除零件部分，加入適量焊錫，讓烙鐵頭完全

 熔化焊錫為止。

 用吸錫線或吸錫器，將零件焊接點上的焊錫，逐一除去。

5.移開零件。

6.清除殘餘焊錫

移開零件後，再次用吸錫線或吸錫器，清除殘餘焊錫。

7.關閉電源

8.長久不使用，應拔出電源插頭

　等待若干分鐘，發熱元件確實冷卻後，再行收拾或離開。

FEATURE:

• Precision temperature control: ~330∞ C (~626∞ F)

• Super slim, pen-like style for greater control and visibilty

• Specially designed for repairs to cell phones and PC boards

• Conductive soldering stand

• Dual voltage AC 110/220V

PRECAUTIONS

1. Caution-High Temperature Operation

 The SS-201 operates at very high temperature. At all times observe

careful operating procedures.

2. Do not use the unit near ignitable gases, paper or other inflammable 

 materials.

3. Never touch the hot tip, with your hands.

4. After use, be sure to let the unit cool down.

5. White smoke may occasionally be emitted near the tip. This is

temporary and caused by very small pieces of dirt on the unit.

6. Never drop or sharply jolt the unit.

7. Do not disassemble the unit unless replacing the heating barrel.

8. Unplug the SS-201 station when not in use for prolonged periods.

OPERATING INSTRUCTIONS

1. Check voltage, 110/220V.

2. Plug the power cord into the power supply.

3. Turn the power switch to ON.

4. Adjust the temperature control knob. Start with a low temperature.

Gradually increase the setting by turning the temperature knob clock-

wise until the desired temperature is achieved.

5. When you have finished using the unit, turn the power setting to OFF.

If you will not be using the SS-201 for a prolonged period, unplug the

unit.

6. Follow instructions for soldering tip care below.

GENERAL CLEANING

The outer case of the iron or station may be cleaned with a damp cloth

using small amounts of liquid detergent. Never submerce the unit in

liquid or allow any liquid to enter the case of the station. Never use

solvent to clean the case.

焊接步驟

1.電源插頭插入電源插座。

2.按開電源開關。

 發熱元件開始發熱。

 調整溫度控制鈕，稍等一會兒，待溫度穩定下來。

 我們建議您，可調整溫度在攝氏300度至350之間。

 注意：溫度如果超過攝氏400度以上，將快速破壞烙鐵頭上的保護層，

 降低烙鐵頭使用壽命。

3.熔化焊錫

手持電烙鐵，取適量焊錫，接觸烙鐵頭尖部，讓烙鐵頭熔化焊錫，除

 了可以去除烙鐵頭上氧化物外，也可以保護烙鐵頭。

 除去多餘焊錫。

4.焊接

 對準並預熱所要焊接部分，加入適量焊錫，讓烙鐵頭完全熔化焊錫為

 止。

 注意：銲錫或錫膏的品質，將直接影響焊接品質，我們建議你，使用

 較高品質的焊錫。

5.電烙鐵離開焊接點，輕輕置放於烙鐵架內。

6.檢視

用電烙鐵進行焊接是快速有效的，但如不小心也可能導致空焊斷路或

 焊接短路…等問題，我們建議您焊接後，應再次仔細檢查焊接情況。

LOW

HIGH

MINI SOLDERI

G ST

TION

MINI SOLDERING STATION

OFF

HIGH

LOW

SS-201

溫度

控制

電源

開關

AC 110/220V

切換開關

保險絲

250V/0.5A 20mm

MINI SOLDERING STATION

OFF

HIGH

LOW

SS-201

Temperature

control

Power

switch

AC 110/220V

adjustment

Fuse

250V/0.5A 20mm

CONTROL PAD OPERATION

(正面圖)

(背面圖)

(Front)

(Back)

使用前，請先確認您所使用的電壓，並將機殼後方的

AC 110V/220V開關，撥至適當位置。

注意：

Warning

Please make sure the exact voltage before use and adjust

the AC 110/220V power switch behind the frame to the correct position.

BEFORE YOU START

Warning

Before using the unit for the first time, please ensure that voltage setting

(AC110/220V) on the back of the unit is set to the correct position for

your location.

MINI SOLDERING 1

Summary of Contents

Page 1 - MINI SOLDERING

81276345PROKIT'S INDUSTRIES CO., LTD.寶工實業股份有限公司SS-201www.prokits.com.twMINI SOLDERINGSTATION更換烙鐵頭 注意：更換烙鐵頭前，一定要先拔除電源插頭，確認在沒有電源和烙鐵頭溫度冷卻情況下操作，以免觸電

Comments to this Manuals

No comments

Prokits-industries SS-201 User Manual

Browse online or download User Manual for Power tools Prokits-industries SS-201. Prokit's Industries SS-201 User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Power tools Prokits-industries SS-201